plastic yielding
英 [ˈplæstɪk ˈjiːldɪŋ]
美 [ˈplæstɪk ˈjiːldɪŋ]
网络 塑性屈服
双语例句
- Analysis of Crack Tip Plastic Zone for Composites under Small Scale Yielding
小范围屈服条件下复合材料裂纹尖端塑性区分析 - A tension member may fail by plastic yielding.
拉伸元件可能由于塑性屈伏而破坏。 - She was no longer plastic clay, yielding imprint to each new experience.
她不再是一团可以随意捏塑、愿意接受每一个新的经验印记的沃土了。 - Plastic deformation takes place first at the crack tip and spreads across the solid as the applied load is increased beyond general yielding.
塑性变形首先发现在裂纹顶端，当工作载荷超过了普通屈服时，则传播到物体中。 - The lead extrusion dampers ( LED) were designed by the plastic yielding ability of the lead.
利用铅的塑性变形能力，设计制作了铅挤压阻尼器。 - In the iteration, the structural factors, i.e. the elastic responses of internal cells to their initial strains, are introduced to correct the predicted plastic strain increments under each incremental load until the effective stresses in the plastic zone turns back to the yielding surface.
其原理是利用结构因子即内部单元对其初应变的弹性响应来校正每步增量载荷作用下预测的塑性应变增量，使塑性区的等效应力逐步返回到屈服面上。 - By means of Lagrange duality theory of the convex program, a dual problem of Hill's maximum plastic work principle under Mises 'yielding condition was derived and whereby a non-differentiable convex optimization model for the limit analysis were developed.
藉助于凸规划的Lagrange对偶理论，建立了Mises屈服条件下理想刚塑性材料Hill最大塑性功原理的对偶问题，并据此建立了极限分析的一个不可微凸规划模型。 - Rate form elasto-plastic constitutive equation with arbitrary yield function has been developed and its specific form under Hill plastic anisotropy yielding model is also given.
推导了具有一般屈服函数形式的弹塑性速率型本构关系；给出了用于板料成形的Hill塑性各向异性屈服模型下本构关系的具体形式； - Growing cucumber in plastic shed in spring is an important cultural method for attaining to early maturing and high yielding.
春大棚黄瓜是黄瓜早熟丰产的重要栽培方式。 - It is presented that the material at the transition region is the easiest region to satisfy plastic yielding conditions and produce thickness compressive strain.
提出内高压成形中圆角和直边的过渡区材料最易满足塑性屈服条件，并发生厚度方向的压缩应变，因此在过渡区易发生剧烈的减薄变形； - In this paper, through using the elastic plastic theory, the author have theoretically analyzed the stressing state, rule of yielding, calculation of stress and strain and mechanical property of the compressed through axis short column of steel fiber concrete packed by steel tube.
运用弹塑性理论，对钢管包钢纤维混凝土短柱轴心受压的受力状态、屈服准则、应力与应变计算和力学特性等进行了理论分析。 - The materials are assumed to be rigid-perfectly plastic. Modified Coulomb failure criteria with tension cut-off are adopted to predict yielding of concrete.
材料性质采用理想的刚塑性模型，混凝土屈服准则采用不考虑混凝土拉应力的修正的库伦屈服准则。 - For linear strengthening elastoplastic material under Shear bending, the plastic theory is unable to obtain an analysis solution of shear stress distribution because there is no corresponding yielding function.
塑性理论对线性强化弹塑性材料在剪切弯曲时横截面上的剪应力分布，由于无法给出相应的屈服函数而不能获得解析解。 - It is obvious that the figuration of the plastic zone is different with various yielding criterion.
由于使用的塑性准则不同，使得洞周的塑性区形状及位置也各异。 - The total deformation of soils consists of three parts: elastic strain, the plastic strain related to the volumetric yielding mechanism and the plastic strain related to the shear yielding mechanism.
土体总的变形由3个部分组成：弹性应变、与体积屈服机制相关的塑性应变和与剪切屈服机制相关的塑性应变。 - The plastic constitutive model which involves DP yielding principle and relevant flowing principle was selected for high pressure conduction medium pyrophyllite.
文章为高压传压介质叶蜡石选择了一个塑性本构模型，它包括DP屈服准则和相关联的流动准则。 - For the layered reservoir with sandstone and mudstone, the stress concentrating is normally found in the contiguity part between the casing and the joint layers of this two kinds of rocks after the plastic yielding;
对于砂岩-泥岩分层储层，在发生塑性屈服后，两种性质不同的岩层交接处与套管接触部位容易产生应力集中和变形突出；